RailFX Aluminum Railing Systems deliver an all-in-one solution for your next project. Our team of experts are happy to help and make sure you are taken care of at every step.
- Up to 5′ Post Spacing.
- 1/8″ – 316 Stainless Steel Cable*.
- Cable Fasteners included with the system.
- Seamless top rails — available in lengths up to 20 feet.
- Easy to trim top rails (on site).
- All posts are pre-drilled for cable and also conceal the fittings and hardware.
- Custom colors are available.
- Low Maintenance. Install and Enjoy!
*1/8″ stainless steel cable is recommended for residential applications. Additional cable diameters are available, contact us for additional information and pricing.
Design Your Railing System
Step 1 - Choose Your Infill Option
Step 2 - Choose Your Top Rail Option
Step 3 - Choose Your Post Mounting Style
Step 4 - Choose Your Finish Color
Choose 1 of our 4 Stock Colors or Match a Custom Color to your Home or Project
FlexFX Program
The FlexFX Program – a simple and flexible railing fitting option that improves any view and makes your living space look and feel larger. The FlexFX Railing option from RailFX® allows you to incorporate these same fittings into any residential railing application with ease. Ideal for both interior and exterior projects, our FlexFX stainless steel fittings and cable are perfect for decks, docks, balconies and stairways that use wood posts, metal posts or composite sleeves. Made in the USA with pride!
You will need at least one Tensioner per run of cable. Pictured are common combinations of tensioners and non-tensioners. FlexFX fittings are engineered to be used with FlexFX cable only.
Cable Railing Kits
RailFX Cable Railing Kits come with Stainless Steel Cable Railing Hardware Fittings for both ends of your cable run, along with all washers and fasteners necessary. Your choice of 1/8″ or 3/16″ diameter 1×19 Type 316 stainless steel cable and installation instructions.
Cable Railing Kits come in cable length increments of 5′ to 70′ lengths. You will then cut the cables to their proper lengths on site. Each kit contains one cable plus all associated hardware for that cable.
Accessories, such as mounting tabs, cable cutters and other installation aids and equipment can be ordered separately. For coastal applications in a salt water environment, it is strongly recommended that E-Z Clean is purchased along with any kit. While Type 316 stainless steel, the most corrosion and rust-resistant stainless steel available, is used almost exclusively in our hardware, it is stain-less steel, not stain-proof. If you’re near the ocean, some maintenance will be required.
Fitting Types
Non-Tensioning fittings are coupled with tensioning fittings to support the cable as it is tightened to the appropriate level to pass your local building code requirements.
Tensioning: Every cable run needs at least one tensioning fitting to ensure the cable can be made taut enough to pass your local building code requirements.
Cable Kit 601 Series - for Wood Posts
Wood Post 601 Series Cable Kit
The 601 Series Kit can be used with both existing or new install wood posts. One of the fittings will install through-the-post and the other fittings will mount to the face of the post. The 3½” Invisiware® Receiver can easily tension the cable with a standard 3/16″ Allen wrench while the Push-Lock® Lag allows you to simply push the cable into the fitting.
RailFX 212 Series Kit
Straight cable runs and cable runs through one corner are the perfect applications for the 212 Series Kit. There needs to be dedicated end posts for each run, and posts situated such that the back side of the posts are all accessible, meaning you can use a through-the-post configuration.
For metal posts, a minimum of 1-1/2″ outside diameter is required. Included in the kit is a tensioning Invisiware® Receiver fitting. The receiver installs through the post on one end and a Pull-Lock® fitting is installed through the other end.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn, using a double corner post configuration is required.
RailFX 232 Series Kit - for Metal Posts
Straight cable runs and cable runs through one corner are perfect applications for the 232 Series Kit. There needs to be dedicated end posts for each run and posts situated so that the back side of the posts are all accessible, meaning you can use a through-the-post configuration.
For metal posts, use a minimum of 2″ outside diameter for this kit. Included is a tensioning Invisiware® Receiver fitting. The receiver installs through the post on one end and a Pull-Lock® fitting is installed through the other end.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required.
RailFX 262 Series Kit
RailFX 272 Series Kit - for Wood Posts
The 272 Series kit can be used with existing post or new wood post installs. Both fittings install through-the-post for a beautiful view with very little exposed hardware. The 3½” Invisiware® Receiver can be easily tensioned with a 3/16″ Allen wrench and the Push-Lock® Stud with a 2-5/16″ Receiver tensioners on both ends allowing this kit to go around two 90˚ turns. This kit is ideal for cable with longer runs.
RailFX 300 Series Kit - Composite Sleeve Posts
Straight Runs with Sleeved Posts:
For sleeved wood posts, use the 300-C Series cable kit. The tensioning device is an Adjust-a-Body® with Hanger Bolt, which lags into the wood post on one end. A Push-Lock® Lag is lagged into the other end.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required as illustrated in Deck 2.
RailFX 300 Series Kit - Wood Posts
Sstraight Cable Run
For wood posts, use our 300 Series. The tensioning device is an Adjust-a-Body® with Hanger Bolt, which lags into the wood post on one end. A Push-Lock® Lag is lagged into the other end.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required as illustrated in Deck 2 below.
RailFX 500 Series Kit - Composite Sleeved Posts
Cable Runs on a Pitch
Top posts are often corner posts, which may require the stair run to connect to the face of your post. The top and bottom of the cable run would be connected perpendicular to those posts, only the intermediate posts would be drilled on the angle for the cable to run through.
Use the 500 Series for sleeved posts with an outside diameter greater than 4½”.
The tensioning device is an Adjust-a-Body® with Threaded Eye, which attaches via a mounting screw to the lag eye, threaded tab or extended length lag eye, depending on the kit.
A Push-Lock® with Threaded Eye attaches the same way to the other end.
As it is not recommended to bend cable through a sleeved post, stair to landing for sleeved posts would be two separate runs.
RailFX 500 Series Kit - Metal Posts
Cable Runs on a Pitch
Top posts are often corner posts, which may require the stair run to connect to the face of the post. The top and bottom of the cable run would be connected perpendicular to those posts and only the intermediate posts would be drilled on the angle for the cable to run through.
Use the 500 Series for metal posts. The tensioning device is an Adjust-a-Body® with Threaded Eye, which attaches via a mounting screw to the lag eye, threaded tab or extended length lag eye, depending on the kit. A Push-Lock® with Threaded Eye attaches the same way to the other end.
The 500-M Series is perfect for going up a stair and across a landing.
RailFX 500 Series Kit - Wood Posts
Cable Runs on a Pitch
Top posts are often corner posts, which may require the stair run to connect to the face of the post. The top and bottom of the cable run would be connected perpendicular to those posts and only the intermediate posts would be drilled on the angle for the cable to run through.
Use the 500-W Series for wood posts.
The tensioning device is an Adjust-a-Body® with Threaded Eye, which attaches via a mounting screw to the lag eye, threaded tab or extended length lag eye, depending on the kit. A Push-Lock® with Threaded Eye attaches the same way to the other end. The 500-W Series can be used to go up a stair and across a landing by inserting post protector tubes ( CS-TUBE ordered separately) in the break-over post. The tube will prevent the cable from carving a groove into your post over time where it exits at an angle.
RailFX Basic 102 Kit
A through-the-post configuration is the ideal scenario for our Basic threaded stud kits. The threaded studs are a functional fitting (not a hide-in-the-post solution). A Brass Hex Nut and some metal thread (both covered by an end cap) will extend beyond the back of the post on one end. A Pull-Lock® fitting is installed through the other end.
For either wood or metal posts, use the 102 Basic Series. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one of your end posts.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required.
The Basic 102 Series kit is offered with cable lengths from 5′-70′. Each kit contains the cable and hardware needed to complete each (1) run.
Tools Required for Installation
• 5/32″ Drill Bit
• 1/4″ Drill Bit
• 29/64″ Drill Bit
• 1/8″ Hex Wrench
• 7/16″ Wrench
• RFXPL-KEY
• Cut Off Kit (mandrel)
• Cut Off Kit (wheel)
Order our Installation Kit along with your Cable Kit to ensure you have the required tools needed.
Part Number INSTL-KIT-100_200
RailFX Professional 224 Kit
Straight cable runs and cable runs through one corner are ideal applications for the Professional 224 Series Kit. There needs to be dedicated end posts for each run and posts situated so that the back side of the posts are all accessible, meaning you can use a through-the-post configuration.
For wood or metal posts a minimum of 1-1/2″ outside diameter. A tensioning Invisiware® Receiver fitting is included. The receiver installs through the post on one end and a Pull-Lock® fitting is installed through the other end.
When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required.
Required Installation Tools
• 5/32″ Drill Bit
• 3″ Combo Wrench
• 1/4″ Drill Bit
• RFXPL-KEY
• 29/64″ Drill Bit
• Cable Gripper
• 1/8″ Hex Wrench
• Cut Off Kit (mandrel)
• 3/16″ Allen Wrench
• Cut Off Kit (wheel)
Order our Installation Kit along with your Cable Kit to ensure you have the required tools needed.
Part Number INSTL-KIT-100_200
Cable Railing Accessories
We understand each project is different. That’s why RailFX has a line of cable railing accessories to help you personalize your railing system and keep it beautiful for years to come.
Fitting Types
• Non-tensioning fittings are coupled with tensioning fittings to support the cable as you tighten it to the appropriate level to pass your building code requirements.
• Tensioning- Every cable run needs at least one tensioning fitting to ensure the cable can be made taut enough to pass your building code requirements.
Anodized Aluminum Cable Brace
Cable Brace for level run:
This Cable Brace is a 3/4” x 3/4” square tube and 42” long. They can be cut down to any size to match the top rail height. Holes are pre-drilled at 3-1/8” on center (13 holes total). The cable brace can be utilized between structural posts to reduce cable deflection when wood or composite sleeved posts are spaced 6’-8’ apart. Use cable brace plugs (included) to attach to top and bottom rail or your deck.
Part Number: RFXCB-42-AN-AL-13
Anodized Aluminum Cable Brace - Stairs
Cable Brace for Stair:
This Cable Brace is a 3/4” x 3/4” square tube and 42” long. They can be cut down to any size to match the top rail height. It comes un-drilled so slots can be drilled on-site to match the cable angel for your stairs. The cable brace can be utilized between structural posts to reduce cable deflection when wood or composite sleeved posts are spaced 6’-8’ apart. Use cable brace plugs (included) to attach to top and bottom rail or your deck.
Part Number: RFXCB-42-AN-AL
Black Aluminum Cable Brace
Cable Brace for Level Run:
This Cable Brace is a 3/4” x 3/4” square tube and 42” long. They can be cut down to any size to match the top rail height. Holes are pre-drilled at 3-1/8” on center (13 holes total). This cable brace can be utilized between structural posts to reduce cable deflection when wood or composite sleeved posts are spaced 6’-8’ apart. Use cable brace plugs (included) to attach to top and bottom rail or to your deck.
Part Number: RFXCB-42-BL-AL-13
Black Aluminum Cable Brace - Stairs
Cable Brace for Stair:
This cable brace is a 3/4” x 3/4” square tube and 42” long. They can be cut down to any size to match the top rail height. It comes un-drilled so slots can be drilled on-site to match the cable angle for your stairs. This cable brace can be utilized between structural posts to reduce cable deflection when wood or composite sleeved posts are spaced 6’-8’ apart. Use cable brace plugs (included) to attach to top and bottom rail or for your deck.
Part Number: CB-42-BL-AL
Brace Connector Plug for Flat Runs
Cable Brace Floor Plate
Our Cable Brace Floor Plate is used in conjunction with the stainless steel cable brace. It is used for mounting cable braces to the top or bottom rail of your railing system or to your deck floor. Dimensions are 2-1/4” x 1-1/4” x 1/4” and it has a #4 Finish Stainless Steel.
Part Number: RFXFLP-CBS
Install with 1/4” Flathead SS Screw, purchased separately.
Post Protector Tube
This Tube keeps the cable from biting in the wood. The post protector tube is inserted into a wood post where the cable enters/exits the post at a angle to protect your wood from wear over time.
Stainless Steel Cable Brace
SS Brace is available in 1/4” x 1” and in 2 lengths: for 36” or 42” high rails. Holes pre-drilled at 3-1/8” on center, 10 holes in 36″ length, 12 holes in 42″ length. Brace is for use between structural posts to keep cables code compliant on level runs. Weld to metal frames or use cable brace floor plates for attaching to wood.
Type: 316 Stainless Steel
Order CB-34.5-SS-10 or CB-40.5-SS-12
Stainless Steel Cable Brace for Stairs
SS Cable Brace is available in 1/4” x 1” and in 2 lengths: for 36” and 42” high rails. Slots are pre-drilled at 3-1/8” on center, 10 slots in36″ length, 12 holes in 42″ length. For use between structural posts to keep cables code compliant on stair runs. Weld to metal frames or use cable brace floor plates for attaching to wood. Must be field-chambered to match stair angle.
Type 316 Stainless Steel
Order CBS-34.5-SS-10 or CBS-40.5-SS-12
Stainless Steel Cleaner and Protectant
Dissolves minor corrosion and leaves a protective coating that lasts for months.
Includes an 8-oz. spray-on rust and stain remover and a 4-oz. bottle of protectant.
Order E-Z CLEAN
Cable Cut-Off Tool
Our cut-off tool is used to cut cable flush with the end of a Pull-Lock fitting and to cut excess threads off stud-type tensioners. Includes mandrel and two cut-off wheels.
Part Number: RFXCUT-OFF KIT
Cable Cutter
For burr-free cutting of your cable.
For Light-duty use to cut 1/8” cable: order C-7
To cut cable 1/4” diameter and under: order C-9 (pictured).
To cut cable up to 3/8” diameter: order C-12
Small Cable Gripper
As an alternative to a large cable gripper, this small gripper will clamp on the cable while tensioning to keep your cable from unraveling.
Part Number: CG-4-6-RFX
Cable Gripping Pliers
Locking pliers have machined jaws to grip your cable as you are tensioning it. Keeps your cable from turning and also prevents damage to the cable when cable is being tensioned.
Part Number: PLIERS
Cable Release Key
This is a must! Releases cable from Push-Lock® and Pull-Lock® type fittings before cables are tensioned (in case of a mistake). For 1/8” cable only.
Part Number: PL-KEY
Cable Tension Gauge
Easily check the tension on your cables with these easy-to-use gauges.
For cable diameter of 1/8”, 3/16” and 1/4”: Order PT-CR
For cable diameter of 1/4” through 3/8”: Order PT-3
Push-Lock® Lag Driver
Our Push-Lock® Lag Driver is designed to simplify installing your one-piece Push-Lock® Lags into wood posts. The driver slides over the wrench flat on the fitting, allowing you to turn the Push-Lock® Lag into the post with either a ratchet or a drill.
Call today: 855-473-9663 or print out the form below and email it to Debi@FBDecking.com or Fax: 888-360-3474